ASTM F2317_F2317M-26
Standard Specification for Design of Weight-Shift-Control Aircraft
| Označení normy: | ASTM F2317_F2317M-26 |
| Vydáno: | 01.05.2026 |
| Status: | Active |
| Počet stran: | 11 |
| Sekce: | 15.09 |
| Označení: | hang point; trimmer; weight-shift-control aircraft; |
| ASTM označení: | ASTM F2317/F2317M |
| Nahrazuje: | F2317_F2317M-16A |
This specification covers the minimum requirement for designing, testing, and labeling of weight-shift-control aircraft. This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot. Flight requirements are specified for: (1) proof of compliance including hang point and trimming setting; (2) general performance such as (a) stall speed in the landing configuration, (b) stall speed free of control limits, (c) minimum climb performance, (d) flutter, buffeting, and vibration, (e) turning flight and stalls, and (f) maximum sustainable speed in straight and level flight; (3) controllability and maneuverability such as general, longitudinal, and lateral control; and (4) longitudinal stability and pitch testing. Structural requirements specified include: (1) strength requirements, (2) fulfillment of design requirements, (3) safety factors, (4) design airspeeds, (5) flight loads, (6) pilot control loads, (7) ground loads including landing gear shock absorption, and (8) emergency landing loads. Design and construction requirements are specified for: (1) materials, (2) fabrication methods, (3) self-locking nuts, (4) protection of structure, (5) accessibility, (6) setup and breakdown, (7) control system evaluated by operation test, (8) mast (pylon) safety device, (9) cockpit design, and (10) markings and placards. Powerplant requirements including installation, fuel system, oil system, induction system, and fire prevention, as well as equipment requirements such as powerplant instruments, miscellaneous equipment, and lap belts and harnesses, are detailed. Operating limitations such as load distribution limits are also specified.
1.1 This specification covers the minimum airworthiness standards a manufacturer shall meet in the designing, testing, and labeling of weight-shift-control aircraft.
1.2 This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot.
Note 1: This section is intended to preclude hinged surfaces such as typically found on conventional airplanes such as rudders and elevators. Flexible sail surfaces typically found on weight-shift aircraft are not considered hinged surfaces for the purposes of this specification.
1.3 Weight-shift-control aircraft means a powered aircraft with a framed pivoting wing and a fuselage (trike carriage) controllable only in pitch and roll by the pilot's ability to change the aircraft's center of gravity with respect to the wing. Flight control of the aircraft depends on the wing's ability to flexibly deform rather than the use of control surfaces.
1.4 This specification is organized and numbered in accordance with the bylaws established for Committee F37. The main sections are:
Scope | 1 |
Referenced Documents | 2 |
Terminology | 3 |
Flight Requirements | 4 |
Structural Requirements | 5 |
Design and Construction Requirements | 6 |
Powerplant Requirements | 7 |
Equipment Requirements | 8 |
Operating Limitations | 9 |
Keywords | 10 |
Annex | Annex A1 |
Appendix | Appendix X1 |
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.