ASTM B0122_B0122M-20
Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar
| Označení normy: | ASTM B0122_B0122M-20 |
| Vydáno: | 01.10.2020 |
| Status: | Active |
| Počet stran: | 6 |
| Sekce: | 02.01 |
| Označení: | copper-nickel plate; copper-nickel rolled bar; copper-nickel sheet; copper-nickel strip; copper-nickel-tin plate; copper-nickel-tin rolled bar; copper-nickel-tin sheet; copper-nickel-tin strip; copper-nickel-zinc plate; copper-nickel-zinc rolled bar; copper-nickel-zinc sheet; copper-nickel-zinc strip; UNS No. C70600; UNS No. C70620; UNS No. C71000; UNS No. C71500; UNS No. C71520; UNS No. C72200; UNS No. C72500; UNS No. C73500; UNS No. C74000; UNS No. C74500; UNS No. C75200; UNS No. C76200; UNS No. C77000; |
| ASTM označení: | ASTM B122/B122M |
| Nahrazuje: | B0122_B0122M-16 |
This specification establishes the requirements for copper-nickel-tin, copper-nickel-zinc, and copper-nickel alloy plates, sheets, strips, and rolled bars made from UNS C70600, C70620, C71000, C71500, C71520, C72200, C72500, C73500, C74000, C74500, C75200, C76200, or C77000 alloy. Each product should be manufactured by hot or cold working, and annealed if required, to produce a uniform wrought structure that meets the specified temper properties. This specification also contains information on the standard tempers for and tensile strengths of hot-rolled, cold-rolled, and annealed tempers. In case of disagreements, the chemical composition is determined following appropriate methods listed here. Grain size is the standard requirement for all products in the annealed tempers.
1.1 This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar. The following alloys are covered:
|
|
| Nominal Composition, % | ||||
| Copper Alloy | Previously Used |
|
|
|
| Chro- |
| UNS No.2 | Designation | Copper | Nickel | Zinc | Tin | mium |
|
| ||||||
| C70600 | ... | 90 | 10 | ... | ... | ... |
| C70620 | ... | 90 | 10 | ... | ... | ... |
| C71000 | 6 | 80 | 20 | ... | ... | ... |
| C71500 | 5 | 70 | 30 | ... | ... | ... |
| C71520 | ... | 70 | 30 | ... | ... | ... |
| C72200 | ... | 85 | 15 | ... | ... | 0.5 |
| C72500 | ... | 89 | 9 | ... | 2 | ... |
| C73500 | 1 | 72 | 18 | 10 | ... | ... |
| C74000 | 9 | 70 | 10 | 20 | ... | ... |
| C74500 | 3 | 65 | 10 | 25 | ... | ... |
| C75200 | 2 | 65 | 18 | 17 | ... | ... |
| C76200 | 8 | 59 | 12 | 29 | ... | ... |
| C77000 | 4 | 55 | 18 | 27 | ... | ... |
Note 1: Plates of copper-nickel alloy Copper Alloy UNS Nos. C70600, C70620, C71500, C71520, and C72200 for use as tube plates in surface condensers and heat exchangers are covered by Specification B171/B171M.
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.